2005 Dodge Verna Window Regulators Save up to 40% on original replacement 2005 Dodge Verna maintenance and repair parts. Over 200 high-quality, direct-fit parts for a 2005 Dodge V. LMC Truck offers 1972-93 Dodge Truck 1974-93 Dodge Ramcharger Front Door Window Regulators and Parts.
If the one of the windows on your Dodge Dakota truck is cracked or broken, you need to replace it. If the window glass itself is intact but not rolling up or down properly, the problem is likely the regulator. If you need to replace the window glass and/or the regulator, you need to get inside the door by removing the inner trim panel. The exact process can differ depending on the year of the truck and whether or not the door has components like speakers installed.
Removing the Door Panel
Step 1
Pry off the controls for the power windows using a trim stick. If the Dakota has manual windows, work a cloth between the window crank and the door to disconnect its clip and remove the crank.
Step 2
Remove the door panel's retaining screws with a screwdriver. Their main locations are along the panel's bottom edge and within the inner door handle.
Step 3
Pull the door panel upward to release its hooks from the door, then raise it off the door. Disconnect all wiring harness connectors and the handle link rod.
Step 4
Peel back the plastic water shield on the door and pry the inner weather seal out of the door glass opening. https://abyellow927.weebly.com/motic-usb-20-driver.html.
Remove the door's speaker by removing its mounting screws, lifting it out and disconnecting the electrical connector.
Repairing the Window
![Dodge Dodge](/uploads/1/3/3/2/133275957/607825353.jpg)
Step 1
Raise the window to where you can access the glass' retaining nuts, then remove the nuts with a wrench (they may require a Torx wrench).
Step 2
Tilt the glass forward to remove it from the track and then lift it out of the door.
Step 3
Remove the mounting fasteners for the window regulator, unplug the electrical connector and remove the regulator from the door.
Step 4
Install the replacement regulator into the door, bolt it to the door and track and connect the electrical connector.
Step 5
Slide the window glass into the door, fit it into the regulator and track and bolt it in place.
Reconnect the inner trim panel in the reverse order of removal.
Tip
- If you need to replace the regulator but not the glass, push the glass up off the frame after removing its bolts and tape it to the door.
Items you will need
- Trim stick or cloth
- Screwdriver
- Wrench
- Window glass
- Window regulator
- 'Chilton Dodge Durango/Dakota Repair Manual'; John Wegmann; Haynes North America; 2006
- Black car and buildings image by Christopher Dodge from Fotolia.com
More Articles
Answer
Wiki User
10/20/2011
Hello, this is straigh from the dodge repair manual. If you needpictures let me know John
Roll window down.
Remove window crank, if equipped.
Remove screw attaching trim panel to outside mirror frame.
Remove screws attaching pull cup to door.
Using a trim panel removal tool, disengage clips aroundperimeter of trim panel, attaching trim panel to door.
While holding bottom of trim panel away from door,simultaneously lift upward and inboard.
Disengage power mirror switch connector, if equipped.
Free browsers for windows 7. Disengage power window/lock switch connectors from switch panel,if equipped.
Separate trim panel from door.
Remove door trim panel .
Peel waterdam away from adhesive around perimeter of inner doorpanel
Remove the door waterdam .
Remove nuts attaching door glass to window regulator.
Remove glass from door or move glass to full up position andsecure glass to door with tape.
Disengage power window motor wire connector from door harness,if equipped.
Dodge Ram Window Regulator Roller
Remove bolts attaching window regulator to inner door panel.
Separate window regulator from door panel.
Dodge Dakota Window Regulator Replacement
Extract window regulator through access hole in inner doorpanel. Free anatomy book download pdf.